• What E-Cigarette?
  • Easy DIY E-Liquid Calculator
  • E-Cig Glossary
  • What is a E-Cig?
  • About
What E-Cigarette

Easy DIY E-Liquid Calculator

Easy DIY E-Liquid Calculator for mixing juice for your electronic cigarette. Just fill out the form to get your recipe. Get the perfect PG/VG mix, nicotine strength and flavour. Make sure to bookmark this easy DIY e-liquid calculator to keep it handy.

For high quality and low cost pre-made e-liquid we recommend CigElectric’s E-liquid.

User Input
Ingredients
Nicotine BasePGVG Flavour BasePGVG
Nicotine Base Strength mg/ml
Target Nicotine Level mg/ml
Amount to Create ml
Flavour Percent %
PG % %
Drops per ml drops/ml

More than 1 flavour?NoYes
Flavour Mixer Input
F1 F2 F3 F4 F5 F6 F7
%

==========================================================

Recipe Output
Recipe ml drops
Nicotine Base
Flavouring
PG
VG

Flavour Mixer Output
F1 F2 F3 F4 F5 F6 F7
ml
drops

  • Enter up to 7 different flavours to get your perfect flavour mix. (Click “yes” for “more than one flavour?”)
  • Set the base liquid of your nicotine and flavouring to either PG or VG to get an accurate PG/VG ratio recipe.
  • Adjust the drops per ml to match your pipet size or bottle top. Useful for making small batches where measuring the exact ml might be difficult.
  • If you get “PV/VG not poss” this is because your PG/VG ratio is not possible due to the dilution requirements or amounts of your base liquids. You either need to change the ratio or use a different base for your flavouring and nicotine.

I hope you find this e-liquid calculator useful. Check out the rest of the blog for electronic cigarette reviews and more!

The following two tabs change content below.
  • Bio
  • Latest Posts

Benji Waters

Hi i'm Benji Waters, electronic cigarette enthusiast and  blogger on whatecigarette.co.uk. I am a serious 'vaper' and very passionate about our freedom to use electronic cigarettes. Follow me for electronic cigarette news, opinions and reviews.

Latest posts by Benji Waters (see all)

  • Recipe: Golden RY4 - July 29, 2015
  • What E-Cigarette Review: iClear Electronic Cigarette Starter Kit - July 10, 2015
  • New study shows chemicals in electronic cigarettes pose minimal health risks - August 12, 2013

223 Thoughts on “Easy DIY E-Liquid Calculator”

  1. Gary on December 21, 2016 at 6:40 pm said:

    I used the calculator for 30ml 50/50 6mg nic 10% TFA Grape and taste nothing, added more grape and even more grape up to 10 ml and still taste next to nothing. New coil still mostly vg taste. Any ideas.

    Reply↓
    • Benji Waters on December 22, 2016 at 7:01 am said:

      Sometimes less is more, You could try less flavouring or do a google search for the specific flavouring and see what % other people are using. If that fails maybe you need to try a different flavour!

      Reply↓
  2. Keith on December 9, 2016 at 2:08 pm said:

    Hey, I bought 960 ml of 70/30 VG/PG at 3mg nicotine premix. I bought a 120 ml of diluted flavoring to add to this premix. I read that I should stay somewhere around 12-13% on this particular flavoring. If I add the 120 ml flavoring to the 960 ml premix VG/PG, it looks like I will be around 13% on flavoring. Does that calculation seem correct right?

    Reply↓
  3. Stephen Mc kenna on November 14, 2016 at 2:11 pm said:

    Hi I want to make a 10 ml bottle with a 6 mg strength I’m not using nicotine I will be using a 50/50 pg vg mix. How many drops of flavour should I add.

    Reply↓
  4. jason chapple on October 31, 2016 at 7:04 pm said:

    hi i bought 500ml of pre mixed juice from bluestar i know it needs steeping its 30pg/70vg and 18mg nic it smells disgusting so i have ordered 50ml of concentrate if i add this will it make it good do you think

    Reply↓
  5. Shaun on October 26, 2016 at 8:45 pm said:

    Hi I am a newbie andni might sound thick here everything seemed to work out well with the calculator expect I don’t understand the drops per ml USBA simpler way to explain this as I don’t want to mess up my first batch yeah I probs guess to some this bill be a daft question lol cheers

    Reply↓
    • Shaun on October 26, 2016 at 9:10 pm said:

      Sorry i was ment to say is there an easier way to understand the drops per ml and flavour strengh I don’t want it to strong or too weak

      Reply↓
      • Benji Waters on December 22, 2016 at 7:02 am said:

        drops per ml is only used if you don’t want to measure in ml’s, and you want to mix using drops only.

        Reply↓
  6. Dylan on October 9, 2016 at 11:07 am said:

    70/30**

    Reply↓
  7. Dylan on October 9, 2016 at 11:00 am said:

    Hey Benji i wanted to make 50ml bottle with 70/20 PG/VG with no nicotine how much flavour would i put into this?

    Reply↓
    • Benji Waters on December 22, 2016 at 7:03 am said:

      The flavour amount is completely up to your taste preference and specific flavouring used.

      Reply↓
  8. Tami on September 28, 2016 at 6:53 pm said:

    Please help, so lost and trying to quit smokes. I have a variety of 10ml flavour bottles that are pg and vg, I’m assuming 50/50. and a large 100gm/100ml pure nicotine. I just want to mix up one bottle at a time to make it simpler. I want lots of flavour and a decent amount of nicotine to satisfy cravings. Am I right to calculate that I mix 2.5mls of nicotine to 7.5mls of flavour juice using a syringe. Then I’m ready to vape? Please help. Thankyou for your site, it’s the least confusing so far if I’m understanding it correctly.. Never been so lost in my life!

    Reply↓
    • Tami on September 28, 2016 at 6:59 pm said:

      Or I just simplified it and got 1/7ml ratio… Oh man :(

      Reply↓
      • Tami on September 28, 2016 at 7:10 pm said:

        Or is it 1/10 ratio because my nicotine is so strong? So sorry to be such a bother hey!

        Reply↓
        • Benji Waters on September 28, 2016 at 8:31 pm said:

          Hi Tami. If you want strong nicotine go for around 20mg/ml. That means you put Nicotine Base Strength = 100 and Target Nicotine Level = 20.

          I would recomend starting your Flavour Percent at 10%. You will need some unflavoured PG or VG to add to the rest of the mix. Otherwise you will have no control on your flavouring percentage and it will be far to strong.

          Reply↓
  9. Damion Bell on September 21, 2016 at 5:26 pm said:

    Hi benji,

    I’ve been using your calculator for almost a year now and it’s helped me out a lot! !!

    Easy to use, all fields are self explanatory, I don’t know how it could be simpler.

    For those that struggle with mixing, I use vampire vape flavour concentrates and mix 65/35 VG/PG at 15% flavour and they come out a treat every time.

    Blackjack is the only flavour I’ve found that develops a lot over time and have found 8 weeks to be the point where it is at its best, all others I start using straight away.

    Happy vaping guys, mixing your own is a heck of a lot cheaper, make your own could aswell to bring your costs down even further!!! It costs me £5 for enough wire & cotton wool to make approx 80 coils and I’ve had some last as long as 6 weeks

    Reply↓
    • Damion Bell on September 21, 2016 at 5:27 pm said:

      Make your own coils*** Damn auto correct!!!

      Reply↓
  10. Alex Jones on September 5, 2016 at 11:32 am said:

    Hi Benji, I’ve seen CBD e-liquid bottles that say something like “250mg CBD” in a 10ml bottle.
    I want to make my own CBD e-liquid but I can’t work out how I go about working out the mg of the CBD per 10ml bottles.
    If I were to buy 250mg of CBD crystals and disolve them in a set amount of the VG or PG …lets say 10ml of PG …is there a way now that I can work out how many drops of that CBD/PG liquid to use in a 10ml bottle to acheive 250mg of CBD?
    If you can help me work this out I would really appreciate it. I can’t seem to get my head around it and it’s really annoying me.
    Many thanks for your time, Alex.

    Reply↓
    • Benji Waters on September 5, 2016 at 11:40 am said:

      Hey Alex, I don’t have any experience with CBD but if the bottles are saying they have “250mg CBD” per 10ml bottle (not 250mg/ml), then you just dilute your 250mg of crystals into your 10ml e-liquid and then you have it.

      Reply↓
  11. Zoe on August 9, 2016 at 2:40 pm said:

    I’m just getting started making my own vape Juices with a CBD component & your calc has been very useful & easy to use. Thanks for the help.

    Reply↓
  12. Mo on August 8, 2016 at 2:49 pm said:

    I want to make 10 mils of eliquid with 50/50 pg/vg and 24mg of nicotine how would I work this calculator? thank you

    Reply↓
  13. Mandy on August 6, 2016 at 12:46 pm said:

    Just used you calculor to mix my e liquid. Very easy thanks

    Reply↓
  14. Jan on July 26, 2016 at 6:13 pm said:

    Hi. If I use ag 80vg 20 distilled water on e liquid calculator,do I need to put dialutet section 20?

    Reply↓
  15. Mark on July 22, 2016 at 8:23 pm said:

    Thanks for this – really helps with making up eliquid in different strengths and quantities.

    Reply↓
  16. Stuart Smith on July 20, 2016 at 2:00 pm said:

    This might be a daft question, although I have been told there is no such thing.

    In the calculator it asks if your flavouring is VG or PG but any site I have been on only states the flavour and bottle size?

    Any help would be great as I am looking to start mixing my own too.

    Reply↓
    • Stuart Smith on July 20, 2016 at 2:04 pm said:

      Also is it best to have your nicotine in the PG or VG?

      You can so tell I am new to this.

      Reply↓
    • Benji Waters on August 26, 2016 at 6:31 pm said:

      Hi Stuart, if the site does not state whether the flavouring is PG or VG it is almost certainly PG based, as this is most common and VG flavourings are usually only made available for people that are allergic to PG

      Reply↓
  17. Carol on July 5, 2016 at 7:46 pm said:

    Hi Benji, i bought my husband the wrong liquid 1.8, he usually uses 1.2 oops what can he add to bring the strength down?

    Reply↓
    • Benji Waters on August 26, 2016 at 6:32 pm said:

      Diluting the liquid by a third will reduce the strength to 1.2%

      Reply↓
  18. Darren on June 24, 2016 at 5:01 pm said:

    Hi
    Another noob, would I be right in thinking that if I require AG rather than VG. I would set PG to my desired 60% and the calculator would give me a VG-AG of 40%.
    Many thanks

    Reply↓
    • Benji Waters on August 26, 2016 at 6:33 pm said:

      Hi Darren, that is correct.

      Reply↓
  19. Vapeoholic on June 22, 2016 at 4:24 am said:

    I got some nicotine that is 60pg40vg 3mg mix how do I use that in my calculator any one can help me out

    Reply↓
  20. darren foster on June 9, 2016 at 11:38 am said:

    hi im new my mate dose my stuff but i want to do my own and want to but 200 ml bottles were can i get my own from …and dose the pg have to be nicotine and the flavour on vg as i dont want to get this wron or can it just be vg or do you have to have both help anyone plzzzz thanx

    Reply↓
  21. chris underhill on June 5, 2016 at 8:48 pm said:

    Brilliant calculator, so easy to use. Get a 1ml and a 10 ml syringe and it’s child’s play! Saved so much money and saved disappointment from weak flavoured e liquid.
    Top man, thanks.

    Reply↓
  22. kevin scuffil on June 2, 2016 at 9:36 am said:

    Wow, just starting to mix my own,finding your calculator almost a godsend
    getting on a bit, (old man) your calculator simplicity personified well done.

    Reply↓
  23. Paddy on May 19, 2016 at 9:30 pm said:

    Hello
    I am looking for a E-Liquid Calculator like this for my website, do you know can I get it for wordpress.

    Reply↓
    • Benji Waters on August 26, 2016 at 6:37 pm said:

      Hi Paddy, I made this on WordPress, you are welcome to link to it through your site.

      Reply↓
      • Gaz on September 12, 2016 at 11:48 pm said:

        Any chance of the code or the code to make it a plugin please for personal use on my blog? I would of course link your site as the original author of the calculator.

        I however don’t want folk leaving my site via a link to use the calculator hence the code. As I said I would of course link your site as the original author of the calculator. Thanks in advance

        Reply↓
      • Mark higgins on September 26, 2016 at 7:52 pm said:

        Im a newbie to so if i want to say make a 30ml bottle how much flavour wld i need to add plz

        Reply↓

Comment navigation

← Older Comments
 

Leave a Reply to Darren Cancel reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Ad

Recent Posts

  • Recipe: Golden RY4 July 29, 2015
  • What E-Cigarette Review: iClear Electronic Cigarette Starter Kit July 10, 2015
  • New study shows chemicals in electronic cigarettes pose minimal health risks August 12, 2013
  • Easy DIY E-Liquid Calculator July 30, 2013
  • The Future of Electronic Cigarettes and Nicotine July 22, 2013

Recent Comments

  • Benji Waters on Easy DIY E-Liquid Calculator
  • Benji Waters on Easy DIY E-Liquid Calculator
  • Benji Waters on Easy DIY E-Liquid Calculator
  • Gary on Easy DIY E-Liquid Calculator
  • Keith on Easy DIY E-Liquid Calculator

Archives

  • July 2015
  • August 2013
  • July 2013
  • June 2013
  • April 2013
  • March 2013
  • September 2012

Categories

  • e-liquid
  • Electronic cigarette
  • mods
  • news
  • Nicotine
  • Recipes
  • reviews
  • Uncategorized
  • Variable Voltage

Meta

  • Log in
  • Entries RSS
  • Comments RSS
  • WordPress.org
© Copyright 2021 - What E-Cigarette
Infinity Theme by DesignCoral / WordPress